Industrial Grunge Step By Step.

Morning all, I am sharing an older post here that was shared when I was asked to be a guest designer that was a bit of a step by step.

The whole piece was not shared here before so I thought I would dust it of and put it up.

All the products used are from the Decoart Media Line.

 

My wall hanging is an assemblage of smaller pieces gathered together.

I started with a small pre Gessoed Canvas and after a base coat of white I built up and blended my colours using Decoarts Media Fluids, Translucent yellow oxide, Quinacridone burnt orange and Quinacridone gold before edging the canvas with black archival ink.

The middle and bottom sections have both been cut from foam board. The middle section has been made from two layered sections of board. The base was painted With Raw Umber and then a coat of Decoarts Crackle paint (this comes white but is easily coloured with the fluid acrylics)

once dry I added some washes of black and quinacridone gold to give an aged and tarnished look.

The top board was given a base coat of white and then a coat of Green Gold this is a really bright almost citrus green/yellow colour, it was looking a little to bright so some more washes of black and quin gold were added to grub it up.

If you are not sure what I mean by a wash, its when you really water down the paint. The fluid acrylics are pretty much pure pigment so the colour stays true even when thinned down. I add a small amount of paint to my craft mat and then start adding water with my brush till I get the results I am after. If you apply the wash and its to strong in colour, just spritz the piece with water to dilute and get the finish you are happy with. The chipped edges have just been painted on by hand using Raw Umber.

The decals are from 7 Gypsies and are rub ons.

The main focal piece comes from a kids Airfix model and has been given a tarnished brass finish that I 

picked up on Andy Skinners Timeworn Techniques online class.

The Bottom section was coated with Decoarts Modelling paste and was applied patchy and randomly, I wanted the surface to have some texture.Once dry the edges were coated with their texture paste.

Again a base of white was added and then a slightly watered down coat of colbalt blue. A few colour washes were added to pick out the low spots. Finally the edeges and rust runs were added by painting Quin gold and just scrubbing it into the textured sections

The red box was also from the model kit and painted to look like an old metal unit.

The top section has been made from a mixed media board from Tando-creative these are laser cut boards made from grey board.

I used a diamond plate embossing folder, coated the board with texture paste once dry a coat of white paint and then a coat of Panes Grey media fluid acrylic.

paint over with some quin gold and let dry, this starts to bring out a really nice rusty look, If you want to go a little further you can add a wash of Red Iron Oxide and just let it dry naturally.

The finishing touches were added, Tim's tap head has been painted with the Patina antiquing cream, left to dry and then just rubbed back to reveal the metal.

Some rust wire was added from the industrial box to the machine.

A few other embellishments were added, a couple more Tim pieces and a light bulb from one of my dads old cars (don't worry, he had accumulated lots of car bits while he was still around)

Thanks as always for stopping by xx

Decoart Crackle Paste ATC - De Stempelwinkel and a Shabby Box

 

Morning all.

I'm sharing over at De Stempelwinkel.

Jetske has just got several of the Decoart Media mediums in stock and I have been playing with the Crackle Paste and Antiquing Creams to come up with a steam punk ATC.

If you have time it would be lovely to see you over there and if you have time you can check out our latest challenge theme on our new challenge blog.

 

I am also sharing this little shabby chic box I painted using the Decoart Chalk Paint and Stencils.

 

 

For the last few months I have been busy shabby chicing loads of things as I have taken the plunge and opened a stand at the new Christchurch Emporium in Dorset

It opened last weekend and it was amazing to see the number of people that turned up on opening day. I was back there this weekend and this is one of the new pieces I added. I picked the box up a few weeks ago and it was beautiful but just plain wood.

I used Decoarts Chalk Paint 'Vintage' and gave the box a couple of coats to get a nice even coat.Using a sanding block and medium grade paper I distressed the box and finished by give a final sanding with some fine grade paper.

Using 'Relic' the stencilling was added and then sanded back to make it look distressed. The box was finished with a couple of coats of satin varnish.

 

Ill be sharing more pics of the stand soon. xx

Thanks for stopping by.

 

De Stempelinkel - Tribalish Tag

Morning all, It's time again over at De Stempelwinkel for a little share.

I have a little tribalish tag to share using the Decoart Media Fluids and stamps from De Stempelinkel.

It would be great to see you over there xx.

De Stempelwinkel - ATC With A Twist

Morning all and thank you for stopping by x.

It's my turn over at De Stempelwinkel today.

I'm working on a new ATC mixed media workshop at the moment and this is my first play at trying something a little different.

My ATC was kindly cut for me by